AUTONET TV

Flat Tire? Three?s the Charm (Tire Repair)

For most drivers, at some point you’re going to have a flat tire. Depending on how it was damaged, it may have to be replaced.  But sometimes, a repair will do the trick, as long as the puncture isn’t on the sidewall and the hole is smaller than ¼ inch/6.35mm in diameter. Here are the three common ways your tire can be fixed.

One way is to put a plug in the hole.  Since most tires are damaged by running over sharp objects such as screws and nails, the small hole from which the air is escaping is on the part of the tire that touches the road. If it’s in the sidewall, it most likely can’t be fixed.  

In the plug method, a technician inserets a rubber plug.  It is covered with some sticky, gluey stuff, and is pushed into the hole from the outside. That plugs the hole and stays in place, thanks to the glue. Friction from driving heats it up and seals the deal.  

Another method is to patch the hole.  For this, your tire has to first be taken off the vehicle, then off the rim so the technician can get access to the inside. There, they’ll clean the inside surface around the hole and apply a rubber patch with an adhesive on it. This type of patch works well, and because of the extra steps and complexity, costs more than having your tire plugged.  

There’s also a combination of those methods just described, the plug-patch.  It is, in essence, a type of patch with glue on it that has a plug sticking out of it.  The plug is inserted into the tire from the inside and pulled through the hole from the outside, drawing the attached patch tight against the tire’s inside surface. The last two methods can’t be used if the hole is near another repair or the sidewall.    

The good news is if it’s fixed properly, your repaired tire should give you good service.

Hans Imports
7275 Post Rd
North Kingstown, RI 02852
(401) 295-7785
http://www.hansimports.net

Bad Vibrations (Brake Rotor Replacement)

If you’ve ever stepped on your brake pedal and felt your vehicle vibrate, that’s a signal that you shouldn’t ignore.  A pulsating brake pedal is a sign that something is wrong.  Braking action should be smooth, sure, and quiet, not shaky and noisy.

Most newer vehicles have disc brakes, called that because they have a round, flat disc connected to each wheel.  Those discs are the rotors. Other parts called brake pads are squeezed against those discs when you press on the brake pedal.

Remember that vibration we mentioned? That can be caused by the rotor not having a straight, true surface. Rotors can heat up from friction and warp.  They can become thinner from constant wear.  Rotors can rust from the elements they’re exposed to, such as rain, snow ice, and salt.  They can get grooves in them from so many contacts with the pads. 

The signs of worn rotors are vibrations, grooves on the rotor (which you can see sometimes through open spots in the wheel) noise such as squealing or scraping when you brake, and increased stopping distance.   

While it used to be common for rotors to be machined (shaved down to restore their flat surface), newer vehicles have thinner rotors, so your service adviser may suggest you replace rotors when they start showing signs of significant wear.

Brakes are important safety equipment for every vehicle.  They enhance your control while driving, so it’s important that they be regularly inspected and maintained.  A good time is when you have your tires rotated. A technician can then look at all components of your brakes and recommend any service you may need to keep your brakes in top shape.

Hans Imports
7275 Post Rd
North Kingstown, RI 02852
(401) 295-7785
http://www.hansimports.net

Don't Blow a Gasket! (Valve Cover Gasket Replacement)

When you head out to your vehicle after it's been parked and notice oil leaking underneath it, that's something to have looked at right away.  Oil leaks mean your oil level is probably low and running a vehicle in that condition can lead to expensive repairs.

While there are many reasons oil leaks develop, one possibility is a bad valve cover gasket.  Vehicle engines have a cover bolted over the spot where the engine valves are, and that cover keeps the oil inside the engine. In between the cover and the engine is a gasket that keeps that seal tight.  But after many years of high engine temperatures and vibrations, that gasket or the bolts that hold on the valve cover can fail or loosen, and oil can leak.

You may see dirty oil on the valve cover in the engine compartment, near the spark plugs, or around the bolts that hold the valve cover on.  All those are signs of leakage and time to bring your vehicle in for our technicians to check out.

In some vehicles, taking off the valve cover and replacing the gasket is a relatively easy job. In some models, though, other engine parts are located near that part of the engine and must be removed to get at the gasket, so repair costs can vary widely.

The technician will measure to make sure the valve cover isn't warped so it can be reused. If it is warped, they'll recommend replacing it with the gasket.  

While the technician has that area of your engine accessible, they will also check to see if other components need replacing at the same time, which could save you money.  And because valve cover gaskets usually fail in older vehicles, the technician will check for other oil leaks then, too. 

One of the best ways to be sure your valve cover is doing its job is to have your vehicle regularly maintained.  The technician will periodically look over your engine compartment and make sure you know when things are showing signs of age and wear BEFORE they fail and leave you stranded.

Hans Imports
7275 Post Rd
North Kingstown, RI 02852
(401) 295-7785
http://www.hansimports.net